Repair guide : WiFi & Bluetooth Interconnect Cables iPhone 6

Level : Medium Time : 35 min Author : Louis O.
600 people have done this repair successfully ! Why not you?
This guide is for replacing the WiFi and Bluetooth interconnect cable.
Symptoms : no WiFi network, bluetooth does not work, low signal
Some advice before you start
Repair - Repair guide: WiFi & Bluetooth Interconnect Cables iPhone 6
Guide format : Pdf Integrate

Step 1

Before disassembling the WiFi and Bluetooth interconnect cable of your iPhone 6, you have to securely turn it off.

Maintain the power button on the top for a few seconds.

Then slide to the right to "power off" button in red.

Step 2

The SIM card tray of the iPhone 6 can be found on the right side of the phone, near the power button (on/off/sleep).

Insert the SIM card eject tool in the small hole and push to eject the SIM tray.

Then grab it and remove it.

The iPhone 6 SIM card tray is now removed.

Step 3

With a pentalobe screw driver, remove the two screws circled in red on the picture.

Those screws are on both side of the lightning connector of the phone.

Those two screws maintain the bottom part of the screen on the iPhone's frame.

Step 4

Then put the iSclack on the iPhone 6.

The suction cups have to be as close as possible to the home button of the iPhone as shown on the picture for a better grip.

Make sure the suction cups are well fixed to the iPhone and peel the two suction cups off the iPhone.

Step 5

With a cruciform screw, remove the five screws circled in red.

Those screws hold the front panel cable bracket that you can remove with a pair of tweezers.

Step 6

With a nylon spudger, gently pry up to disconnect the cable for :

   - the front camera,

   - the earpiece speaker,

   - the proximity and light sensor,

   - and the home button cable.

Step 7

Still with a nylon spudger, pry again to disconnect gently the last two cables holding the display assembly of your iPhone 6 :

   - the LCD screen cable,

   - the touch screen cable.

Step 8

You can now pull out the complete display assembly.

The complete display assemble of your iPhone 6 is now disassembled.

Step 9

Use the cruciform screwdriver and remove the two screws circled in red.

Those screws hold the two following connector brackets :

              - battery connector,

              - headphone jack/speaker/dock connector/microphone connector .

Then grab the connector's bracket with a pair of tweezers and remove it.

Step 10

Use the nylon spudger and gently pry to disconnect the battery's cable.

For this guide we recommend that you disconnect the battery for safety reasons. Nonetheless, no need to remove it.

Step 11

With a nylon spudger, disconnect the headphone jack/lightning connector/GSM antenna/microphone cable.

Step 12

Use the nylon spudger again to disconnect the GSM antenna.

Step 13

With a cruciform screwdriver, remove the four screws circled in red.

Those screws secure the logic board and the plastic bracket.

Before removing the logic board, remove that bracket.

Step 14

Now using a flat screwdriver, remove the rivet screw circled in red.

This screw hold the top part of the logic board.

Even if this is a cruciform screw, we recommend that you use a flat screwdriver.

Step 15

Use the curciform screwdriver and remove the two screws circled in red.

Those screws maintain the metal bracket.

Then remove it with tweezers. You can see two connectors and a screw holding the logic board.

Step 16

Still with the cruciform screwdriver, remove the four screws circled in red.

Those screws maintain the WiFi antenna and the logic board.

Step 17

With a pair of tweezers, grab and remove the WiFi antenna.

Step 18

With the cruciform screwdriver, remove the three screws circled in red.

Those screws maintain the metal grounding part of the phone.

With a pair of tweezers, remove it.

Step 19

Use the nylon spudger and disconnect the volume/vibrator buttons cable.

Step 20

Still with the spudger, gently pry to disconnect the power button cable.

Step 21

Disconnect the back camera using the nylon spudger.

Step 22

Insert the spudger between the speaker and logic board.

Then gently pry in order for it to lift.

You can now grab and remove the iPhone 6's logic board.

Step 23

Turn the logic board over with the spudger and disconnect the first and second interconnect cable connector.

Step 24

With the spudger, disconnect the third and fourth interconnect cable connector.

Step 26

The interconnect WiFi and Bluetooth cable is now disassembled.

You can replace it by a new one.

To reassemble your iPhone 6 follow this guide in reverse order.

Comments

Add a comment

They're talking about us

SOSav in the press

  • SOSav on tf1
  • SOSav on france 2
  • SOSav on france 3
  • SOSav on m6
  • SOSav on france info
  • SOSav on 01 net
  • SOSav on l express