Spare parts for smartphones, tablets... English USD

Repair guide : Power Button iPhone 6

Level : Medium Time : 35 min Author : Louis O.
375 people have done this repair successfully ! Why not you?
This guide is for replacing the power button of the iPhone 6.
Symptoms : broken or cracked button
Some advice before you start
Repair - Repair guide: Power Button iPhone 6
Guide format : Pdf Integrate

Step 1

Before disassembling the power button of your iPhone 6, you have to securely turn it off.

Maintain the power button on the top for a few seconds.

Then slide to the right to "power off" button in red.

Step 2

The SIM card tray of the iPhone 6 can be found on the right side of the phone, near the power button (on/off/sleep).

Insert the SIM card eject tool in the small hole and push to eject the SIM tray.

Then grab it and remove it.

The iPhone 6 SIM card tray is now removed.

Step 3

With a pentalobe screw driver, remove the two screws circled in red on the picture.

Those screws are on both side of the lightning connector of the phone.

Those two screws maintain the bottom part of the screen on the iPhone's frame.

Step 4

Then put the iSclack on the iPhone 6.

The suction cups have to be as close as possible to the home button of the iPhone as shown on the picture for a better grip.

Make sure the suction cups are well fixed to the iPhone, then open the tweezers in order to separate the screen from the frame of the phone.

Step 5

With a cruciform screw, remove the five screws circled in red.

Those screws hold the front panel cable bracket that you can remove with a pair of tweezers.

Step 6

With a nylon spudger, gently pry up to disconnect the cable for :

   - the front camera,

   - the earpiece speaker,

   - the proximity and light sensor,

   - and the home button cable.

Step 7

Still with a nylon spudger, pry again to disconnect gently the last two cables holding the display assembly of your iPhone 6 :

   - the LCD screen cable,

   - the touch screen cable.

Step 8

You can now pull out the complete display assembly.

The complete display assemble of your iPhone 6 is now disassembled.

Step 9

Use the cruciform screwdriver and remove the two screws circled in red.

Those screws hold the two following connector brackets :

              - battery connector,

              - headphone jack/speaker/dock connector/microphone connector .

Then grab the connector's bracket with a pair of tweezers and remove it.

Step 10

Use the nylon spudger and gently pry to disconnect the battery cable.

We recommend that your unplug the battery for safety reason. But there's no need to remove it completely.

Step 11

With the nylon spudger, disconnect the headphone jack/lightning connector/GSM antenna/microphone cable.

Step 12

Use the nylon spudger again and disconnect the GSM antenna.

Step 13

With a cruciform screwdriver, remove the two screws circled in red.

Those screws maintain the angled logic board bracket .

Step 14

Remove it with a pair of tweezers.

Step 15

Use a flat screwdriver to remove the rivet screw circled in red.

This screw maintain the top part of the logic board.

Even if it looks like a cruciform screw, we advise you to use a flat screwdriver to remove this screw.

Step 16

Use a cruciform screw to remove the two screws circled in red.

Those screws hold the upper cable bracket

You can remove it with a pair of tweezers in order to make visible two connectors and the screw holding the logic board.

Step 17

Still using a cruciform screwdriver, remove the four screws circled in red.

Those screws maintain the WiFi antenna and the logic board.

Step 18

With a pair of tweezers, grab the WiFi antenna.

Step 19

Still with the cruciform screwdriver, remove the three screws circled in red.

Those screws maintain the grounding bracket .

With a pair of tweezers, remove that bracket.

Step 20

Use the nylon spudger and disconnect the volume/vibrator buttons cable.

Step 21

With the spudger, gently pry to disconnect the power button cable.

Step 22

Disconnect the back camera using the spudger.

Step 23

Insert the nylon spudger between the speaker and the logic board.

Then gently pry to lift it slightly.

You can now remove the iPhone 6's logic board.

Step 24

The logic board of your iPhone 6 is now disassembled.

Step 25

With a cruciform screwdriver, remove the two screws circled in red.

Those screws maintain the power button cable.

Then peel off gently the cable up from the rear case to access the button.

Step 26

Use a pair of tweezers to remove the power button.

Use tweezers and pull out the power button.

Step 27

The power button of the iPhone 6 is now disassembled.

You can replace it by a new one.

To reassemble your iPhone 6 follow this guide in reverse order.

Comments

Add a comment

They're talking about us

SOSav in the press

  • SOSav on tf1
  • SOSav on france 2
  • SOSav on france 3
  • SOSav on m6
  • SOSav on france info
  • SOSav on 01 net
  • SOSav on l express