Spare parts for smartphones, tablets... English USD

Repair guide : Power Button iPhone 5S

Level : Hard Time : 70 min Author : Alexandre
160 people have done this repair successfully ! Why not you?
This guide is for replacing the power button of the iPhone 5S.
Symptoms : broken or cracked power button
Some advice before you start
Repair - Repair guide: Power Button iPhone 5S
Guide format : Pdf Integrate

Step 1

Before disassembling the power button of your iPhone 5S, you have to securely turn it off.

Maintain the power button on the top for a few seconds. Then slide to the right to "power off" button in red.

Step 2

Use a pentalobe screw to remove the two pentalobe screws holding the front panel.

Those screws are circled in red on the picture.

Then insert a iSclack to pull the entire front panel as shown on pictures 2,3 and 4.

Step 3

Then press the iSlack to remove it .

Don't remove the screen just yet, it is still attached by a few cables, the home button/touch id cable being one of them.

Tip : If your screen is broken or cracked, we suggest that you put some tape to cover the screen in order to remove it more easily.

A metal bracket is on the home button cable.

Remove it with a pair of tweezers.

Step 4

Use the nylon spudger to disconnect the home button cable.

Step 5

Gently lift the display assembly to a 90° angle as shown on pictures 1 and 2.

Remove the four screws circled in red with a cruciform screwdriver.

Those screws secure the screen connector bracket.

Make sure to remember the spot of each screw. They have different characteristics. You have to put them back into their original spot.

Step 6

Use the pair of tweezers and remove the screen connector bracket.

Step 7

Use the spudger to disconnect :

- The front camera/microphone/earpiece speaker/light and promixity sensor cable

- The LCD screen cable.

Step 8

Still with a nylon spudger, disconnect the Touch screen cable.

Then grab the display assembly and remove it.

The complete display is now disassembled on the iPhone 5S.

Step 9

With a cruciform screwdriver, remove the two cruciform screw circled in red.

Those screws maintain the battery connector bracket and the dock connector.

Use a pair of tweezers to remove the bracket connector.

Step 10

Use a nylon spudger to disconnect the following cables :

  - Battery connection cable,

  - Back camera connection cable.

Step 11

Still using a nylon spudger, disconnect the dock connector.

Step 12

Disconnect the power/volume button cable with a nylon spudger.

Then use its tip to disconnect the GSM antenna.

Step 13

Use a SIM card tool eject and insert it in the SIM card hole. Push to eject.

The SIM card tray is on the right side of the iPhone 5S.

Step 14

Grab the SIM card tray and remove it.

Step 15

Peel off the black tape on the logic board's top .

Step 16

Remove the 7 screws holding the logic board of the iPhone 5S :

one 2.4mm screw, circled in red on the picture,

two 2.8mm cruciform screws, circled in orange on the picture,

four rivet type screws, circled in green on the picture.

To make it more easier, we advise that you use a flathead screwdriver to remove the 4 rivet type screws.

Step 17

Use a nylon spudger to gently lift the logic board.

Then flip the logic board toward the battery as shown on picture 4.

Do not remove it just yet, it is still connected to the iPhone 5S by the WiFi antenna

Step 18

Use the spudger to disconnect the WiFi antenna.

Remove the logic board.

The logic board of the iPhone 5S is now disassembled.

Step 19

Use a nylon spudger and put it under the battery, pry and lift the battery.

This can take quite some time if there is a lot of glue use by Apple underneath.

Make sure not to damage the battery when removing it !

Step 20

Grab the battery and remove it.

The battery of the iPhone 5S is now disassembled.

Step 21

Use the spudger's tip to remove the rubber back camera bracket.

Step 22

Use a pair of tweezers and remove the back camera of your iPhone 5S.

Step 23

With a cruciform screwdriver, remove the two screws circled in red.

Those screws maintain the power/volume button cable metal bracket .

Still with tweezers, grab the bracket and remove it.

Step 24

With tweezers, remove the black sticker near the power button .

Use a cruciform screwdriver to remove the screw circled in red.

This screw maintain the metal bracket of the power/volume button cable on the right side.

Step 25

With tweezers, remove the metal bracket which has been unscrewed in the last step.

Grab it and remove it from its socket.

Step 26

With the spudger's tip, gently push in the power button.

Then grab and remove it with tweezers.

Step 27

The power button of the iPhone 5S is now disassembled.

You can replace it by a new one.

To reassemble your iPhone 5S follow this guide in reverse order.

Comments

Add a comment

They're talking about us

SOSav in the press

  • SOSav on tf1
  • SOSav on france 2
  • SOSav on france 3
  • SOSav on m6
  • SOSav on france info
  • SOSav on 01 net
  • SOSav on l express