You have trouble turning on or off your iPhone 5C because the power button does not respond? He stays depressed? Moreover, impossible to raise or lower the sound because the volume button does not work anymore? Ditto with the vibrator function that refuses to activate and therefore quickly pass in silence! You are right to turn to SOSav for a solution.
Our experts put at your disposal this illustrated and commented repair guide that explains how to change this tablecloth power, vibrator and volume iPhone 5C yourself for two to three times cheaper than going through a professional. Because yes, you can see that repairing the iPhone 5C is within the reach of all and you will make significant savings! SOSav offers you a quality iPhone 5C power sheet but also all the necessary advice to replace it without going through the genius bar!
Before you start changing the power, vibrate & volume pad of your iPhone 5C, make sure that it is turned off.
Unscrew the 2 pentalobe screws around the lightning connector (charging connector).
To open your iPhone 5C, place an iSclack or Suction Pad on the Universal Tool Kit on the glass.
Isclack mode: Place the iPhone in the holder then press the clip. Operate the clamp, the screen lifts itself.
Suction mode: Place a suction cup as close as possible to the home button. Then gently pull on it to lift your iPhone 5C screen.
For better grip make sure that the suction cup is completely on the glass.
You can now put your screen vertically.
CAUTION: Do not try to remove your screen completely, it is still hooked to the motherboard of your iPhone 5C by several connectors.
Unscrew the 4 screws circled in red holding the connector cover to the motherboard.
Using a pair of pliers, remove the connector cover of your iPhone 5c now.
With the nylon spatula disconnect the 3 connectors from the screen:
- The 1st connector, the cable managing the front camera and the proximity sensor
- The 2nd connector, the cable managing the touch screen.
The third connector, the cable managing the LCD Retina.
Your iphone 5C screen is disassembled.
Unscrew the two Phillips screws circled in red that hold the cover protecting the battery connector.
Now remove the battery cover.
Using a nylon spatula, gently pry the battery connector to disconnect it from the motherboard.
CAUTION: Leverage the battery connector and not the connector on the motherboard. This could very heavily damage your iPhone 5C.
Insert an iSeasmo spatula (or nylon spatula) between the battery and the iPhone 5C chassis to pry the battery and lift it off. Insert this spatula at the top.
CAUTION: Do not damage the WiFi antenna your iPhone 5C located near the point of insertion of the spatula.
Disconnect with the spatula, the connector buttons power, vibrate and volume.
Also disconnect the cable from the charging connector, again with the spatula.
Then with the spatula still, peel the tablecloth gently without damaging it.
Unplug the antenna, lifting it with the nylon spatula.
Have the SIM drawer ejector supplied with your phone.
Then insert it into the hole provided for this purpose, push it in until the SIM drawer comes out.
Finish extracting the SIM tray as well as the SIM card from your phone.
Repeat the Phillips screwdriver, to unscrew the 6 screws, holding the motherboard to the chassis.
These screws are circled in red on the photo opposite.
Insert the spatula under the motherboard, and make it stand out by lifting slightly.
No resistance should be noticeable.
Grab the motherboard to turn it to the left.
ATTENTION: The motherboard is still fixed by the WiFi antenna, do not shoot.
Now, disconnect the WIFi antenna with the spatula, just by lifting the connector.
Unscrew the 2 screws of the vibrator support with the Phillips screwdriver.
Take the clip to extract the vibrator support for more precision.
Keep the clip to remove the vibrator from its location, to release its connecting web located underneath.
Now unscrew with the Phillips screwdriver, the 3 screws holding the push buttons (volume and vibrator).
Take the nylon spatula to slide it under the tablecloth to unstick it from the chassis of the iphone 5C. Takeoff takes place in several stages.
Here take off the part managing the volume and vibrator buttons.
In this step, take off the vibrator portion.
Then unscrew the 2 screws from the bracket for the rear camera.
Use the pliers to extract this medium.
Then grab the tablecloth to take the camera out of its slot.
Unscrew the Phillips screw holding the flash bracket.
With the spatula, lift the bracket that holds the flash to the chassis.
Then, with the pliers, remove the piece of tape that hides the screw holding the power button.
Now unscrew the 2 screws holding the power button.
It is now possible to lift the flash that is connected to the power button. The latter must leave his home without forcing.
Always with the spatula, lift the entire tablecloth to make sure nothing is stuck / stuck.
Bring the pliers to finish extracting the tablecloth.
No resistance should be felt, if this is the case check the previous steps.
Now your power, volume & vibrator iPhone 5C is completely removed, you can proceed to its replacement if necessary.
To reassemble your iPhone 5C follow this guide in reverse order.
Add a comment